ADSS terminating helix dead end is made of aluminum-clad steel wire, and the pre-twisted wire is preformed into a bundle during processing, and a firm layer of emery is glued to the inner wall to increase the grip of the tension clamp under the condition of reducing the side pressure on the optical cable.
Contact Now
Helical tension set ADSS long span with D shackle, Thimble clevis, helical dead end, protector rods. A dead-end is installed at each end of the cable length to attach to the structures. Two dead ends are used at angle changes of 30 degree or greater, either horizontal or vertical.
Contact Now
Product advantages: 1. There is a large contact area between the clamp and the pull wire, the stress distribution is even, there is no stress concentration point, and the achievable grip strength is not less than 95% of the stranded wire Calculate the breaking force. 2. The dead end preformed guy grip is made of the same material as the pull wire, which has good corrosion resistance. 3. The dead end preformed guy grip is simple to install, without any special tools, and can be done independently by one person.
Contact Now
Dead end clamp is made of plastic body with very high mechanical and climatic resistance. A stainless steel flexible cord equipped with movable insulating saddle and two sleeves compressed on the ends to prevent detachment from the clamp body.An inner sheath consisting of two insulating plastic wedges for clamping of the neutral carrier without damaging the cable insulation.
Contact Now
The medium and high tension strain clamps are composed of a double-layer twisted wire structure. The tensile inner twisted wire is made of galvanized steel wire or aluminum-clad steel wire. The inner wall of the pre-twisted wire is stuck with a layer of fine emery to increase friction. The pre-twisted wire is preformed into four sub-bundles during processing to avoid installation errors and facilitate quick installation. The ends of the pre-twisted wires are bent radially outward to avoid squeezing and damaging the optical cable.
Contact Now
ADSS spiral helical dead end consists of an anchor shackle, thimble clevis and preformed guy grip of suitable length, which used for supporting ADSS fiber optic cable in tension at cable sections, acute turnings or at the terminal pole. -Design for quick and easy installation-Minimizing time consuming civil works -Provide a future proof aerial network-Temperature: -10°C up to +70°CSn Model No. Suitable for ADSS cable range(mm) 300M spanANZ 030/0940 8.6-9.4ANZ 030/1010 9.5-10.1ANZ 030/1070 10.2-10.7ANZ 030/1140 10.8-11.4ANZ 030/1220 11.5-12.2ANZ
Contact Now
ADSS spiral helical dead end consists of an anchor shackle, thimble clevis and preformed guy grip of suitable length, which used for supporting ADSS fiber optic cable in tension at cable sections, acute turnings or at the terminal pole. -Design for quick and easy installation-Minimizing time consuming civil works -Provide a future proof aerial network-Temperature: -10°C up to +70°CSn Model No. Suitable for ADSS cable range(mm) 300M spanANZ 030/0940 8.6-9.4ANZ 030/1010 9.5-10.1ANZ 030/1070 10.2-10.7ANZ 030/1140 10.8-11.4ANZ 030/1220 11.5-12.2ANZ
Contact Now
ADSS preformed tension clamp needs to know the outer diameter and force value of the optical cable to request a quotation.
Contact Now
The ANJ 1280 ADSS guy grip made of galvanized carbon steel wire has 6 no strands or customized based on required technical specification. The guy grips come in a resistant cardboard box or plywood cases with the customer information in the visible part of the outer package.Uses: Used to connect the ADSS optical cable and the pole tower in the ADSS optical cable line erection. The pre-twisted wire protects the ADSS optical cable and improves the anti-vibration effect.
Contact Now
Composition: inner stranded wire, outer stranded wire, embedded ring, PD type hanging plate, U type hanging ring. Purpose: To withstand full tension. Features: a.The outer stranded wire is directly connected to the pole tower through the connecting fittings such as the embedded ring, and bears the line load. b. The inner twisted wire protects the ADSS optical cable.Technical specification: -Design for quick and easy installation-Minimizing time consuming civil works -Provide a future proof aerial network-Temperature: -10°C up to +70°CSn Model No.
Contact Now
Galvanized steel thimble clevis is compatible with dead end application to attach loop type dead end to tongue or eye type fittings. It is usually ductile iron material, hot dip galvanized and with 5/8” dia clevis pin.
Contact Now
The small tension strain clamp is used for the span under 100 meters. It is a single-layer pre-twisted wire structure. It is designed for the small span installation of ADSS optical cable. It is simple and reliable, and the installation is convenient and quick.
Contact Now
ADSS optical cable small tension strain clamp, single-layer twisted wire can be used below 200 meters; high-tension strain clamp, double-layer twisted wire can be used for spans above 200 meters. The technical parameters required for the quotation are: the diameter of the applied wire, the range of use, the tensile force and so on.Preformed tension set usually used for feeder and distribution ADSS cables installation.
Contact Now
Tension set ADSS cables installation requires a special tangent assembly or a mechanical dead end at each pole. Tension clamp helical spiral usually with several numbers of rods, such as 7 of rods and thickness of each rod can be different based on different requirements. 2.5mm is the most often cable sizes. And always be compatible with fitting accessories.Sn Model No.
Contact Now
The thimble clevis is mainly for ADSS light span tension set which made of galvanized ductile iron.All dielectric dead-ends require a proper size and strength thimble clevis or extension link.Technical characteristics:Model No.: TC-02Associated Bolt size: M14Tension strength: 20KNFinish: hot dip galvanized steelCotter pin: stainless steelDrawing: Installation image(part 2):
Contact Now
The construction process is simplified, the materials are easy to carry, and the installation does not require other auxiliary tools. The construction personnel can operate independently after one teaching, and the appearance after installation is smooth and beautiful. Reduce labor intensity and increase labor productivity.
Contact Now
The preformed dead end is used to fix the cable clamp of the cable of the tower, the iron tower, and the microwave tower. It can replace the U-T clamp and the wedge clamp that are commonly used to fix the cable on the line tower. The unique design makes the tension-resistant structure of the cable simple and reliable. After installation, the empty tube formed by the twisting of the two legs of the pre-twisted wire of the wire clip can be wound on the cable to produce a strong grip. The twisted ring is used to fix the ground anchor. Or on the tower pole.
Contact Now
Preformed inner protection line rods:The material is aluminum-clad steel wire, which is the same material as all the aluminum-clad steel wires of OPPC cable. The inner wall of the protector rods is glued with a layer of gold steel sand through a high-strength polymer water-soluble environmentally friendly adhesive to increase the friction with the optical cable. The rods is preformed into four sub-bundles during production, which is convenient for quick installation.
Contact Now
Light short span tension set for ADSS cable diameter 11.0-12.0mm, tension strength 4KN, and max span 120 meters.The tension dead end guy grip is made of galvanized steel wire or aluminum-clad steel wire, and the inner wall of the pre-twisted wire is stuck with a layer of fine emery to increase friction.1.The short span ADSS tension set is used for the installation of ADSS cable, includes ADSS guy grip, Galvanized thimble clevis and U shackle. 2. The structure of the short span ADSS guy grip is simple.
Contact Now
Stay grips dead ends is the preformed wire type, minimum length is 600mm and finish is galvanized. Thimbles is used with guy grips to support wires through the stay rod eye. A combination of guy grips and pole top make offs is used.Installation image:
Contact Now
ADSS optical cable rubber rod down-lead clamp is made of corrosion-resistant, weather-resistant EPDM rubber. It is used for fixing ADSS on the pole tower, suitable for different cable diameters, convenient and reliable installation, and wide adjustable range.1.Function: Fix the optical cable leading up or down on the pole tower to prevent it from shaking and avoid the optical cable from wearing. 2.Condition: The fiber optic cable line and the continuous poles on the first and end poles. 3.Method: usually install one every 1.5 meters.Technical specification table:
Contact Now
Galvanized steel pole top make off is generally double wrapped around the pole. 3 strands plus king wire and effective 7 strand stay length for dead end attachment. top to facilitate termination of the stay strand that firms the pole on the earth.Features:1. Material: galvanized steel wire2. Application: for stay rod assembly3. Dimension: 1750 overall length mm4. Finish: hot dip galvanized5. Stay wire diameter: 12mm6. Tensile strength” 63kNProduction drawing: Installation image:
Contact Now
ODWAC, FTTH Self-supporting butterfly-shaped lead-in optical fiber cable installation accessories, stainless steel clamps, optical cable fixing partsThe fiber is squeezed through the sheet and the sheet, and the fiber is squeezed in the middle to complete the wiring function. The main function is to prevent the wire body from bending and protect the wire body, and the locking position can be moved quickly and simply. It is easy to use, put the optical fiber into the slot, install the pull piece, and tighten it.For self-riding butterfly optical cable 2*6mmBreaking load: 1 kNInstallati
Contact Now
Uses: Used to connect the ADSS optical cable and the pole tower in the ADSS optical cable line erection. The pre-twisted wire protects the ADSS optical cable and improves the anti-vibration effect.
Contact Now