JBTL Insulated PG Clamp-manufacture,factory,supplier from China

Bimetal PG clamp is used in non-strain tapping or connecting to a line suitable for aluminium and copper conductors.Features:M12 bolts and nuts and washers : mild steelFinish: tin platedMinimum ampere rating: 300ATypeConductor mm²JBTL 16-12016-120JBTL 50-24050-240

PVC insulation piercing connector It is suitable for the branching and splicing of overhead insulated wires of 1kV and below. Features:Fully insulated housingStructure sealed, waterproof, anti-corrosion, long lifePuncture structure, torque bolt, ensure puncture pressureDifferent diameter and different wire connection, strong applicability.Model No.Suitable conductor range sqmmMain dimensionsqmmNormal current(A)Bolt noMain lineSub lineABHJBC1/7010-7015-10412355551JBC1/9516-951.5-10412655551JBC-116-12016-1206049802991JBC-250-24050-2407484.51164762

The JJC-2 piercing clamp is equipped with a tightening torque nut. The screws are treated with corrosion resistance. The torque nut makes installation easier, safer and faster. Its constant piercing pressure can ensure the cable connection to achieve the best electrical effect. The puncture has a waterproof function, and can withstand a voltage of 6kv in water without breakdown.

The JJC-2 piercing clamp is equipped with a tightening torque nut. The screws are treated with corrosion resistance. The torque nut makes installation easier, safer and faster. Its constant piercing pressure can ensure the cable connection to achieve the best electrical effect. The puncture has a waterproof function, and can withstand a voltage of 6kv in water without breakdown.

The JJC series of low-voltage cable piercing clamps use excellent insulation materials and sufficient materials, which greatly improves the stability of the product and has a long service life. The product models are complete in variety, stable in size and easy to match. It is used for the branch connection of insulated cables in building power distribution systems, the connection of low-voltage overhead insulated cables, the branch connection of low-voltage insulated incoming cables, and the street lamp power distribution system. Features:1. Main branch： 1.5-25sqmm2.

CAPG copper-aluminum special-shaped parallel clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wire, steel core aluminum stranded wire and copper branch wire. Through the re-processing of the profile, the aluminum density is better after the second forging, and the strength of the wire clip is improved. higher. There is a layer of blue epoxy resin on the inside of the wire clip to better isolate the air from the copper-aluminum welding joint and prevent the electrochemical corrosion of the copper-aluminum.

The power distribution top tie can be used to fix bare or insulated wires in the top grooves of pin insulators and post insulators of the power distribution system.

The energy distribution top tie can be used to fix naked or insulated wires inside the top grooves of pin insulators and submit insulators of the power distribution device.

The bi-metal connector is designed to provide an effective corrosion barrier between the dissimilar metals aluminium and copper.The threads nuts and tapped holes is cut after galvanizing and well greased. All other threads is formed before galvanizing. Each PG is tightened  by two bolts with nuts and washers.

PAL1500 aluminum wedge dead end clamp is used to insulate neutral wire suspension cross-bonded cables(25sqmm to 70sqmm). It can use CS-10 aluminum alloy pole mounted bracket for fix, also can be bolted to the pole with M14&M16 bolt or two stainless steel straps 20mm×0.7mm. Black wedge and wire bail to identify insulated neutral clamp.Features:1. Material: high strength aluminum alloy.

The preformed strain clamp is used to undergo full anxiety on the naked conductors and overhead insulated conductors in the energy transmission and distribution line, and connect the conductors to the stress tower, that could replace the traditional bolt-type stress clamp and compression kind strain clamps and wedge-shaped stress clamps.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the produ

The NLL wedge-shaped strain clamp has the advantages of very small hysteresis loss, light weight, and convenient installation, which meets the requirements of energy saving and consumption reduction in the transformation of the national grid. The main body of the product is made of aluminum alloy, and the bolts and nuts are made of hot-dip galvanized material.Features:1. Model : wedge type2. Material: high strength alloy aluminum3. Model No.: NLL-24. U bolt number: 2 nos M125. Tension strength: 50kNTechnical specification: Model1KV Overhead Insulated wir

Anchoring clamp pole clamp bracket is composed of CS14 cable bracket and ES 1500 suspension clamp. It is used on poles, in alignment or angle, different levels, also provide for hanging a public light bundle. The anchor pole clamp with stable quality, durable and long service life; neat and burr-free; simplify operation, convenient and easy to use.Features:1. Conductor range: 25-95sqmm2. Package:50 pieces3. Gross weight: 17 kg4. Dimension: 54×31×32cm5. Material: high strength alloy aluminum 

NLL wedge-shaped tension clamp body is made of high-strength aluminum alloy; the outer shell is smooth and has a long service life; it is easy to install and use; it has no power loss and is an energy-saving certified product.Features:1. Model : wedge type2. Material: high strength alloy aluminum3. Model No.: NLL-34. U bolt number: 3 nos5. Tension strength: 60kN Technical specification: Model1KV Overhead Insulated wire10KV Overhead Insulated wireWire clamping rangeφ (mm)U-boltNominal failure loadNumberdiameterNLL-125～7010～255.0～10.02M1240NLL-250～120

The PA2000 FTTH plastic tension clamp is designed to anchor insulated service lines with 2 conductors to the pole. The clamp is composed of a body, wedges and removable, adjustable bail. One core adjustable anchor clamp are designed to supporting the neutral messenger, the wedge can be self-adjusted.Features:Unit weight:550gCarton size: 550×410×250mmQuantity per carton : 50 piecesMaterial: Nylon and stainless steelCable diameter: 12-15mmTension strength: 7KNDrawing: 

The preformed strain clamp is used to bear full tension on the bare conductors and overhead insulated conductors in the power transmission and distribution line, and connect the conductors to the strain tower, which can replace the conventional bolt-type strain clamp and compression type strain Clamps and wedge-shaped strain clamps.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the

PAL1000 aluminum alloy optical cable insulation strain clamp is a product suitable for overhead insulated conductors. The product is used for cable pull, aluminum alloy body material, PA66 insulation core, stainless steel wire rope, and the product process is die-casting. The high-quality aluminum alloy material has strong corrosion resistance and is not easy to rust and age. The appearance is neat and tidy, and the unique design can well protect the cable.Features:1. Material: high strength aluminum alloy.

Wire tension hardware for steel core aluminum stranded wire 1. Large grip strength of the clamp and high safety performance. It is used for transmission and distribution lines such as steel stranded wire, aluminum stranded wire, steel core aluminum stranded wire, insulated wire, etc. The pre-stranded strain clamp grip can reach 100% of the stranded wire calculation breaking force or above. 2. The pre-twisted clamp is simple to install and easy to construct. It does not require any special tools. One person can complete the operation.

The tension clamp NLL-1 is suitable for the overhead lines of 10kv and below. It is used to fix the aluminum stranded wire or the steel core aluminum stranded wire on the tension rod. When used for the overhead insulated aluminum wire, it is used in conjunction with the insulating cover to provide insulation protection. The wedge-shaped strain clamp has the advantages of very small hysteresis loss, light weight, convenient installation, etc., which meets the requirements of energy saving and consumption reduction in the transformation of the national grid.

Insulation strain clamp PAL2000 is used for overhead ABC cable, aluminum alloy main body, nylon PA66 insulation core, stainless steel wire rope. The wedge-shaped insulated aluminum alloy tension clamp produced by our company has a variety of specifications. PAL2000 is used for cables with a diameter of 70sqmm to 150sqmm and a tensile load of 15KN. The length of the wire rope can be customized, and the batch quantity can be printed on the product according to customer needs . Features:1. Material: high strength aluminum alloy.

The wire rope clamp is corrosion-resistant, not easy to rust, and has the strength of the wire rope. It is safe to use, beautiful in appearance and smooth in transition. The lifting operation has a large safe load, can resist impact load and has a long service life.

• The elasticity of the C-shaped element can maintain a constant contact pressure between the wire and the clamp for a long time, a constant and sufficiently large contact pressure, and the maximized contact surface can maintain a very low contact resistance for a long time.•Unique structure to ensure that the pressure of the wires (different wire diameters) on both sides is equalized, and the large and small wires are skipped.• Long-term stable and good contact performance: maintenance-free, maintenance-free, reducing maintenance costs.•Scientific and advanced articulated structure, which sav

The wire clamp is composed of a rubber clamp block, a pre-twisted wire and a cast aluminum casing. 1. Enhance the rigidity of the cable hanging point and increase the radius of curvature. The single-line clamp can meet the 30° steering angle, and the double-line clamp can meet the 60° steering angle. 2. It can be ensured that the cable is not subject to large bending stress near the outlet of the wire clamp, so as to avoid local mechanical damage causing strand break or wire breakage.

The suspension support hook clamp made of hot dip galvanized steel, the dimension is 120mm （L）and 10mm as diameter of the hook. There is one hole of M14 punched on the base plate. The thickness of the base plate is 3.2mm.